店铺平面图和平面图需要尽快

我们想要一个自由设计师为我们公司创建一个专业的标题页。我们以前的扉页看起来不太好;请参阅“绝代旧标题页。pdf”文件(请忽略图纸细节)。请参阅此屏幕视频注释:http://bit.ly/Y7Ntwa我们需要这些尺寸的图纸(英制/公制):8"x11"(也需要公制)11"x17"(也需要公制)36"x24"(也需要公制)我们的标志应该包括在标题块上。工作细节请见附件，如有任何问题请告诉我们。有很多即将到来的工作，我们可能会要求最好的控制者在不久的将来帮助解决。注:理想情况下，CAD软件应该是总架构师或AutoCAD格式，可以导入到我们的软件。

一页8 1/2“x 11”，目前手绘，社区要求在“Autocad”上完成。

我有两张我的物业的手绘平面图，需要转换成CAD格式(DWG)和PDF格式。这些是已批准的发展计划，现在需要用于显示修订，以供审查。我有A4和A3的设计图扫描图。图则上的彩色部分用于先前已完成并需要纳入CAD图则的核准修订。

我有一份目前正在建造的辅助生活设施的平面图。我需要一份平面图动画，用于营销材料等。张贴的是我们各自公寓的两种彩色布局图。我还贴了一张黑白的建筑布局图。我想有黑白布局重新制作，以配合彩色布局。对于建筑布局，没有必要包括淋浴、厕所、水槽、家具等细节。使用Sketchup来构建房间布局，建议使用Sketchup来匹配它们。

这个任务需要计算哪些配置文件用于图库结构!在这个任务中不需要设计或绘制任何东西。只计算。附件的计划是由一位工程师为在我的房子里用钢型材建造一个画廊而制定的，但我怀疑他选择的型材是过度的，所以我想听到更多的意见。我向大家保证，我最终会在他的批准下建造画廊。40平方米的画廊将被用作我孩子的两个客厅。它可以放这些房间应该放的普通家具。主梁可以是HEA, IPN或您可能推荐的降低剖面高度的其他剖面。主梁由两个部分焊接而成，连接点下方有一个RHS或IPN支柱。我还不确定柱子的位置，因此我需要计算两种选择的主梁轮廓:390cm + 600cm或270cm + 720cm。 Each part of the main beam might be a different profile so please calculate the minimal required profile for each part. I would also like to know what profile measures I would need if there was to be no pillar in the middle of the main beam and it would be a one piece of 990cm. All other 3 sides of the gallery have an existing wall and part of this wall has an existing reinforced concrete belt (yellow in the drawing). There are also 4 existing reinforced concrete pillars as appears in the drawing. It is planned to have a UPN profile (welded together as one) all along the 3 other sides. The whole structure will be supported by 6 RHS pillars (the main beam middle pillar might be IPN) that will be attached with Jumbo screws and chemical adhesive to reinforced concrete floor. At the back plane of the gallery the 3 RHS pillars are very close to existing reinforced concrete pillars. Is it possible to attach the UPN to the existing pillars and make do without these 3 RHS pillars? The main beam and the back plane will be connected with 15 IPN beams. I still don't know if the length of these beams will be 429cm or 470cm so I need both options calculated. The floor surface will be made of several layers for isolation with 30mm pine wood at the top. I need to know what are the minimal measures for all the profiles in my plan and according to which assumptions the calculation was done. One last question. Above the gallery there is a 10meters wide by 8 meters long wooden shingle roof (as in the photos) that is supported by small wooden pillar in the middle. I need to install a 10meter steel beam from side to side at the middle of the roof so that I can remove the supporting wooden pillars. What would be the minimal IPN profile to use for that? Would IPN 100 or 120 do the job? Calculate the following profiles: Main IPN or HEA beam at 720cm + 270cm (2 different profiles?): Main IPN or HEA beam at 600cm + 390cm (2 different profiles?): UPN: Width IPN beams at 429cm: Width IPN beams at 470cm: RHS pillars: IPN pillar: Roof 990cm IPN beam: Any improvement suggestions are welcome.