定制个人护理/洗发水瓶盲目的

我需要一个单一的3D或2D渲染的“桩筏”基础基础。我将通过以下10个步骤描述如何制作它，但如果读者能够以某种方式直观地看到它，他们将从中受益。插图应该是黑白的，灰色阴影是允许的。混凝土、泡沫、土壤等的标准建筑填充模式是可以的。最终的图形预计将在一本小屋建造的书中出版，并得到插画师的认可。结构描述如下。如果有不清楚的地方，请提出疑问!下面是桩筏基础的施工细节，可能适用于手工挖洞到霜冻线是困难的岩石，根，或密集，压实的till。垫基连接到向下延伸到高承重土的驱动销桩。与销桩的摩擦增加了垫的沉降阻力。 The footing form itself is built of XPS foam, which remains an integral part of the footing insulating against cold penetration from above. Materials per footing: XPS foam insulation (blue or pink) 1 sheet 2’x 8’ x 2” Crack-resistant fiber-reinforced concrete mix (1 80# bag) ½” x 12” concrete anchor bolt 5/8” x 20’ rebar (number depends on driven depth) Construction adhesive (1 tube) Ground-marking paint (1 spray can) Directions: 1) Excavate a square hole 3’x 3’ and ~12” deep. Pile excavated soil on a tarp for later use as backfill. Leave the bottom of this excavation level and soil on bottom undisturbed (important!). 2) Cut four pieces of XPS foam 2’x2’ in size. On 3, find the center, and cut a circular hole with 9” radius (18” diameter) using jig saw or drywall saw. Bond these together with foam-compatible adhesive along the circular cut edge. On the fourth piece of foam, find the center and cut a circular hole with 4” radius (8” diameter). Bond this piece to top of the other three. 3) Lay the XPS form flat on bottom of excavation exactly where the footing/pier will be. Reach inside and spray paint the ground within the form. Then remove the XPS foam form and set aside. 4) Within the painted circle, drive an 8’ length of rebar into the ground as far as it will go, or until just 8” protrudes, whichever comes first. For ease, drive this with a hand-held fence post driver and finish with hand sledge. Cut off protruding rebar 8” above ground (a Milwaukee 12V cordless subcompact bandsaw is an excellent tool for this). 5) Continue in this fashion until you have driven 6 rebar pins, well-spaced, into the footing area, but none closer than 2” to the painted outline of the footing. 6) Using a rebar bender tool, bend the protruding length of each piece of rebar to a ~ 90-degree angle, 3 or 4 inches above the ground. Keep all bends within the footing outline. These bends will lock the rebar into the concrete raft when the footing is poured. 7) Place the previously constructed XPS form on the painted ground surface, enclosing all of the driven pin piles. Mix fiber-reinforced concrete to specifications. Weight form down with cinderblock or large stones and pour mix until it is flush with top of the form. 8) In the center of the 8” diameter hole, insert 12” anchor bolt, pushing through the wet concrete until it hits the ground, leaving 4” exposed. Ensure it’s centered and plumb. Cover exposed concrete with plastic and let the footing cure 72 hours. 9). Cover the form with dirt excavated originally. Grade to drain away from the top of the footing. Seed, and cover with straw until vegetation is established. (Omit this step from drawing....). 10) An 10" diameter round wooden pier will be set on top of this footing. The protruding bolt in the footing will insert in a hole drilled in bottom center of the pier.

这是一种新的儿童玩具，它用绳子和积木、滑轮、马达、手推车、马车、钩子和爪子一起使用。这些组件可以用临时双面胶带连接到墙壁、天花板和地板区域(水平和垂直表面)。以及房间的内外角、窗和门框)。

我正在改造我那600平方英尺的后院谷仓风格的工作室。它已经有了绝缘，电力，门窗，但需要从我们的主屋自来水和下水道。我们希望把它变成一个1卧室/1浴室的地方，但不知道从哪里开始，也不知道如何设计，所以我们通过这次比赛寻找一些想法!附上一个非常基本的想法，我把它留给你的创造力来做剩下的事情。作为参考，我的地址是6150 Pierce St Arvada, CO. 80003。

我想把我的2D图纸转换成3D效果图，用于我们所有的营销材料。

我们公司正在寻找一种独特的室内饮水机。我们正在寻找一个独特的室内喷泉。我们计划在亚马逊上销售，因此，设计是独特的，与平台上的其他竞争对手不同。3.除了一股水流，我们希望喷泉有一个地方放蜡烛或熏香，所以这可以是一个二合一的产品。4.像这样的饮水机应该在室内使用，它们应该在房子里创造一个美妙的环境。一种冥想，平静，放松的感觉，让它在背景中运行。项目尺寸L x W x H:高达9 x 9 x 11英寸产品重量:3磅材料:树脂,供你参考:•100强室内水上喷泉在亚马逊的卖家:www.amazon.com/gp/bestsellers/home-garden/3735981/ref = zg_b_bs_3735981_1•引用一个独特的和独特的设计,结合室内喷泉以及蜡烛/光:www.amazon.com/Alpine-Corporation-Pouring-Tabletop-Fountain/dp/B002YKMPQ6/ref = zg_bs_3735981_2