机器人割草机盲目的

我正在寻找创造一种新型的服装扣件。我希望实现的基本规格如下。该紧固件由两部分组成。盘子:(例如连接到背包上)磁盘(连接到手电筒为例…它插入到板上以形成紧固/锁定)板规格:1。尺寸:不大于17mm × 17mm，深度2-2.5mm厚需要能够容纳一个12毫米的圆(磁盘)，将固定到它。3.插入磁盘的压力磅:目标是10磅或更少4。 Weight that it needs to be able to hold 100 lbs 5. Pounds of pressure to release disk, 10 lbs or less 6. Functionality: Ideally the fastening system would be push in with a 20-25 degree or less "twist" out. Needs to have the ability to "lock" (lock in this case means, not release so that the user can trust the fasteners ability to hold the objects that are attached to it and they will not fall off. 7. Ideally, the plate can accommodate the separation of the insertion force of the disk from the rotational force that allows the disk to release so that it can be placed on different weights of material. DISK 1. The disk can not exceed 12mm in diameter/size and needs to be 3mm (or less) in thickness. 2. The disk will be attached/mounted to a different object that will hold that object to the plate. 3. Ideally requires 20-25 degrees or less of rotation to release from the plate 4. Ideally it can accommodate a straight "snap in" insertion, or a "ski-binding" toe to heel or side to side snap in. A good concept to look at for inspiration is the clips bike peddle. MATERIALS: Open to anything USABILITY: Needs to be able to handle the wear and tear of at least 100,000 insertions and releases without losing its strength. MECHANISM: I am open to any form of mechanism including (but not limited to) electric, magnetic spring, rings, teeth, gears, pins etc. LOOK AND FEEL: Modern American style (think Apple), needs to have clean lines, nice smooth face, with a beveled edge etc. as It will be used on a fashion/apparel product. INSTALLATION: The design needs to consider how the factory will install both the plate and disk onto to their respective materials/accessory.

3轴容量50吨

嗨。我迫切需要做公寓的设计和可视化。我们准备支付良好的金额，如果设计师/可视化器将工作只要你需要。我们有大楼的模型，我把它附在所有文件里了。还有我们寄来的小纸条。将有3个角度:内角和两个外部图像。笔记很简单，但我们想看看你作为设计师的想法。风格是现代或极简主义。我想看到舒适的设计以及逼真的可视化。我们附上了一些图片，作为一个很好的例子。 The time frame is very limited, the project should be with me by Friday evening 30.10.2015 after 13:00 (UTC+01:00). Use common sense in the work. Write in comments and private messages. Good luck!

我们正在寻找一个连接/插件系统的设计。该系统应由两个主要部分组成;1.“底座”将被安装在一个表面上(例如墙)。2.“contro -Base”contro -Base是一个适配器(附件连接-例如一个点)，可以点击/卡扣/滑动到基座上。注意:附件的重量可能高达1公斤(可能在颠簸的环境中)，这需要考虑到“底座”和“反底座”的设计。最好是直径约为7厘米的圆形，高度尽可能低，不干扰设计要求。2.将连接到一个12伏的电源点•12伏的电线从后面(穿过墙壁)或从侧面(在墙上)。 Wires should be easily connected to the bottom of the Base. • The design should take into account easy attachment of the 12 volt wire to the Base by the user. • Also in case the wire is connected from the side of the Base there should be an opening / gate. 4. Will be fixed to a surface using screws. • The design should take into account easy accessibility for the user when mounting on surface. 5. Will pass 12 volt current to the Contra-Base once the Contra-Base is fixed onto the Base through a solution that is: • Low tech • Full proof The Contra-Base: 1. Should click/snap/slide/connect (or other) onto the Base; • Once attached on the Base, the Contra-Base should only be able to disconnect through manual intervention; • The locking mechanism should be very solid and as low-tech and full-proof as possible; • Once locked, the Contra-Base should not be able to turn on the Base, however the placement of the Contra-Base should not be limited by a (single) defined position; • Release mechanism should not be by force, but by intervention. Again, the solution should be as low-tech and full-proof as possible. 2. Should receive the 12 volt current from the Base (see “Base” #5.) and forward it to the accessory (e.g. spot) mounted on the Contra-Base. Requirements: 1. All solutions need to be manufacturable and preferably seamless integrated if possible; 2. To be manufactured using injection moulding with minimal mould complexity; 3. The files should be of a professional quality (including STEP files) so they can be handed over to an Injection Moulding company; 4. Non injection components should be minimal and easily available in the market or easily manufacturable; 5. Modern, minimalistic but high quality look & feel is an absolute must. Also when the Contra-Base is not attached to the Base, the Base should still look good and not technical. Please provide High Quality rendering views + preferably .U3D files during the contest. STEP files required on completion We will award the 1st price ($1500) to the best overall idea that meets – or only needs minor polish to meet – all the requirements We will award a 2nd price ($500) for the best innovative idea for the easy connection solution of the 12 volt wiring to the “Base”. • Needs to be integrated into the design of the “Base”, as low tech as possible and without any complex (expensive) external components. We will award the 3rd price ($500) to the best innovative idea for the 12 volt current transfer solution from “Base” to “Contra-Base” • Needs to be integrated into the design of the “Base” and the “Contra-Base”, as low tech as possible and without any complex (expensive) external components. Attachments: Whiteboard screenshots: 1. Potential Wiring situations; 2. Electrical wire connection to the “Base”; 3. Fixation of “Base” to wall; 4. Fixation of “Contra-Base” to “Base”.

打开我的浓缩咖啡机:为消费者创造独特的体验La Marzocco制造高端专业浓缩咖啡设备。高品质的材料:La Marzocco的目标是在其设备和部件中尽可能多地使用不锈钢。-独特的技术:La Marzocco设计并获得了饱和酿造组和双锅炉技术的专利。-设备由我们位于意大利佛罗伦萨外的工厂的工匠手工制作。特别是，这个项目旨在设计一个全新的包装GS/3 http://www.lamarzocco.com/it/prodotti/gs3.html被认为是业内最先进的专业家用浓缩咖啡设备。在坚固性和抗摔性方面，新包装必须具有与现有包装相似的技术规格，如下所示:防潮箱实验室测试标准:UNI EN ISO 2247 -低频率振动UNI EN ISO 2233 -调节UNI EN ISO 2248 -跌落测试最大堆叠:3箱托盘:根据ISPM 15 Fao, 2000/29或替代法规处理的熏蒸杉木。落下试验:顶点1日10滴,3条边和6面临40厘米项目包含在包:1单位:双重portafilter 1单位:单一portafilter 1单位:干预1单位:编织软管1单位:flex排水软管5过滤器篮子:1 x7gr 1 x14gr 1 x17gr 1 x21gr xblind 1单元:purocaff罐1单位:5毫米六角扳手2单位:铜垫圈排气螺丝1单位:软管夹1单位:软管把握行业2单位:水检测组件1单位:用户手册(A5格式)