Fever Phones
in3D Modeling Designheld byTDLast seen:
Contest Ended, Winner(s) have been selected.
-
Open
-
Choosing Finalist
-
Ended
Description:
The design of this product is a blend of 2 different products, headphones (earbuds) and a children's ear thermometer. there will be a button on the earpiece to trigger the temperature taking action.
Wants:
Google "ear thermometer" for an idea of the in-ear portion (sort of cone shaped). the ear portion shall have an LED light inside the center of it, to illuminate the ear. there shall also be a button on the outside where the adult could press and trigger the device to start sensing. the button should also have an LED light (potentially the same one) on the cable to the earphone jack it should have a small streamlined housing to hold the electronics for the unit, (can be 3/4 inch wide by 1.5 inch long. by 3/8" thick. cable should enter one end and exit the other. at the opposite end of the cable should be a traditional earphone jack such that would plug into an smart phone. the other option would be to have the headphone jack and the electronics housing all in one, in this case it would be 1" x1" and 3/8" thick with a jack out the bottom in one corner and the cable out the side leading to the earpiece. in both cases only one ear piece is needed. not a 'left and right'
Don't Wants:
something that is not manufacturable, nothing blocky or square, prefer smooth lines.
Ask for Sample:
this is a small project, so i think the sample may also be the finished product.
File Size Limit:
5 MB - 9.9 MBEntries
Discussion
Showing last 20 comments -View All
Ravi,
Your design stands out in the crowd.
Nice to have you here...
Keep up the good work :)
Winning is everyone desire..
But winning is not everything...
is how you matured towards it, that counts...
Your design stands out in the crowd.
Nice to have you here...
Keep up the good work :)
Winning is everyone desire..
But winning is not everything...
is how you matured towards it, that counts...
Designer
Mr. Zulfadzryl
Thank you.
Thank you.
Designer
Sir,
I am happy, Very happy.
It is a pleasure to submit my designs and selected as a best design.
Thank you.
Ravi.
I am happy, Very happy.
It is a pleasure to submit my designs and selected as a best design.
Thank you.
Ravi.
Designer
Congrats Ravi...
A thoughts don't argue with buyer it shows lack of professionalism.
Thanks TD for helding this contest here.
A thoughts don't argue with buyer it shows lack of professionalism.
Thanks TD for helding this contest here.
Designer
slow down REDA, next time don't pride with your 5 stars before the winner selected.
Designer
The winning design was submitted after the end of the contest "6 hours after the end"
or are sweet line called? it's anything you really done everything to discourage good designers .....
congrats RAVI
or are sweet line called? it's anything you really done everything to discourage good designers .....
congrats RAVI
Buyer
thank you all for the great contributions, I am sorry there could only be one winner in this case. it was a difficult choice.
Administrator
Hi Troy,
Your contest was closed, that's why you couldn't select a winner. Anyway, you can try now.
Thanks,
Lucian
Your contest was closed, that's why you couldn't select a winner. Anyway, you can try now.
Thanks,
Lucian
Buyer
for some reason CadCrowd is not allowing me to select the winner, I am working with them now...
Designer
who is winner here?
Buyer
Thank you to all contributors, I will be carefully reviewing the submissions over the next 2 days and will notify you as soon as possible. Thank you!
Designer
thank you for your feedback TD
Buyer
we can tap power and communication from the headphone jack:
http://arstechnica.com/apple/2011/01/project-hijack-uses-iphone-audio-jack-to-make-cheap-sensors/
the earphone will not stay in place, it will only be used when taking the temperature.
almost all the designs submitted have some sort of LCD display, i will not need a display on any of these.
thanks,
TD
http://arstechnica.com/apple/2011/01/project-hijack-uses-iphone-audio-jack-to-make-cheap-sensors/
the earphone will not stay in place, it will only be used when taking the temperature.
almost all the designs submitted have some sort of LCD display, i will not need a display on any of these.
thanks,
TD
Designer
Another thought is how can the smart phone be the display unless you have a mini usb connection going to it with a corresponding smart phone app to translate the data? The headphone out can only transmit audio to the speaker.
Designer
So is this supposed to be a headphone that can actually stay in place like earbuds or does it have to physically be held up to the ear? It dont make any sense to be an earphone if it is only going to be used when taking temperature or inspecting ear?
Designer
@Antanas:
Using the right impedance matching, one can harvest power out of the audio-jack.
the HiJack project-illustrates data and power transfer through the jack (http://arstechnica.com/apple/2011/01/project-hijack-uses-iphone-audio-jack-to-make-cheap-sensors/)
Best regards
Using the right impedance matching, one can harvest power out of the audio-jack.
the HiJack project-illustrates data and power transfer through the jack (http://arstechnica.com/apple/2011/01/project-hijack-uses-iphone-audio-jack-to-make-cheap-sensors/)
Best regards
Designer
Hi All ,
5 BiG Stars Have you seen them?
5 BiG Stars Have you seen them?
Designer
1. I checked prices ~ Intel Bluetooth Modules 6,5 € at Mouser catalog http://eu.mouser.com/ProductDetail/Intel/PBA31308V202-S-LJYU/?qs=sGAEpiMZZMsGelYiB%252bjhZpS9PJgNT5YFsCHlUL5fw30QRa38VGf1iA%3d%3d
2. but the battery still need to use - for temperature sensor, LED's and data transfer to smart phone ...
2. but the battery still need to use - for temperature sensor, LED's and data transfer to smart phone ...
Buyer
bluetooth or wi-fi would be great, but then we need batteries. Also, the cost is a critical factor here, and the wireless portion is more expensive. Good suggestion though.
Designer
why you use a cable? - maybe better to connect thermometer with smart phone via Blootooth or WiFi?
Similar Contests on Cad Crowd
Motion sensor
This project is to design the housing for a motion detector for commercial office buildings. it should be approximately 2.5-3.0 inch circle and the body should be no more than 1.0 inch thick. the circle can be bigger if the edges sweep out to with a nice curve back to the ceiling surface. it will mount to a standard t-bar ceiling grid. (the kind of ceiling with the drop in tiles) it should mount in the corner of a light fixture with a portion of the "top" or up facing side exposed to the light fixture. and have a window on the top that looks up at the light... (for a light sensor) the window shall be rectangle and dimensions are: 33.0×10.8mm. the face which points to the room shall have a PIR lens (like this one http://www.jvs.de/Carclo_Fresnel/Drawings/PF68_12076_Drawing.pdf i'd like to receive drawings that are 3d printer ready. ease of mass production and tooling should be considered. drawings should also be open for editing by our team. Our team will add the holders, screws, clips, etc for the Electronics inside. the mounting method could be a small piece of spring steel or plastic. White plastic/PC examples: http://cdn3.volusion.com/jn7vt.cfos2/v/vspfiles/photos/HBL3-2.jpg?1416706843
3D design for a lovely four-leafs clover keyholder
I am looking for a model of a four-leafs clover key holder that would just make me and anyone else fall in love with. If selected it would be an exclusive design. I just need the design of the clover (not the keyring, chain, etc.). I have something very specific in mind. Of course, should be so that it can be realistically produced (technical characteristic of the design - not necessarily the file/program yet). I am looking for something kind of full body, rounded shapes, if leafs kind of remind of a hearth even better, but not main. It really just should look: that's the one. I am attaching a pic of similar objects, just to give you a sense of the full body, roundness ...
Alfred's Mic's Design Contest
阿尔弗雷德的麦克风fi想创造世界rst Modular Microphone. The goal is to create a condenser microphone with interchangeable capsules and circuitry for different studio recording applications. Design requirements: 1. Capsule/ head piece must be removable. 2. Circuitry must be removable. 3. All removable parts must be easy and quick to assemble. 3. All removable components must be lockable onto the microphone body for stability and durability. 4. standard male XLR connection for base 5.Circuitry isn't being designed here, just the process to easily interchange the interior circuitry and head piece/capsule without any rewiring involved for the microphone user.
Clean up old AutoCAD drawings
We have old AutoCAD drawings for a 4000sft residence that need to be converted to ACAD 2013 or 2014 including assigning drawing elements to current Architectural CAD layer standards.
Solidworks Car model
I am looking for someone to model in solidworks a replica of a car already on the market. I like super cars and classic cars! The file needs to be somewhat editable in solidworks and renderable in keyshot. The contest is quite open ended, the more detail the better.
zulfadzryl
Designer